1. Kevin frazier

    Cam degree wheel

    has anyone figured out how to attach cam degree wheel to the crank on front side?
  2. Martin-Brighton-uk

    Exhaust Cam valve gap - it reduces over miles ridden same as intake, not increases right?

    I've seen posts in some threads on here that the exhaust cam clearances increase rather than decrease with miles ridden. Is that right? Yes the exhaust cam clearances are greater than the intake, but both valve wear in the same way don't they, snap closing each time? So the statement that...
  3. Martin-Brighton-uk

    Cam Cover Washer and seal

    Hi all, just doing valve clearances while engine is still out of the frame. Other threads suggest replacing the fancy washer when doing it back up. The parts diagram shows two parts. A washer and a seal. Do you replace both?
  4. Plow Horse

    Dash Cam

    Thinking about installing a camera system on Edsel. I don’t have any experience with any of the different systems available. If anyone has or is using a camera system on their bike, would you recommend that system or suggest a different system and why. Thanks for your reply in advance
  5. Radz94

    Cam ladder torx

    Hello, Trying to get cam ladder torx bolts to break free. I"m concerned of the equal tension. tried heating them but unsure of how much I can get away with. Already broke a socket. Advice would be much appreciated.
  6. Rumbleboomer

    My broken cam...

    Some of you guys may remember last year I had issues with my '07 classic which resulted in a broken exhaust cam. I hate to admit the cause of the problem but it may help someone so I will. This bike was basically new to me with 50k on it when this happened. I removed the oil tank and a small...
  7. Ishrub

    R3 Cam chain 170 link T1143200

    DELETED as I do not want to mislead anyone. This is the correct R3 cam chain. I think the other model Triumphs may use a smaller chain in link number. I would disregard all sources that suggest they are interchangeable...
  8. wjb

    Cam specifics question

    So I've seen in print some impressive results in horsepower from cam swaps, stock to aftermarket (Carpenter, Lush, etc) but I don't think I've ever seen any details of the specifics of those cams. Does anyone have lift and duration numbers from any of those cams? Especially duration @ .050 and...
  9. bebsy

    Triumph cam jig offset

    Tooth alignment offset...???
  10. bebsy

    Cam chain only has 4 links vs 5

    Just purchased a new cam kit upon comparison the chain only has 4 links the one I have taken out has 5? Just been back to triumph and they say its the only chain listed for this model and aren't sure what going on, the sprockets are 38 tooth but visibly narrower. Has anybody come across this...
  11. bebsy

    Cam chain guides

    Well I ordered some parts a set of camchain guides was reasured they were the ones as via my vin number upon checking the parts numbers for both sides are the same? were as in the pic they are different?? . Can anybody put me out my misery pls
  12. daytonageo

    Cam chain replacement

    I was going into do the 20k valve checks and before I started, I checked the cct depth, and it came out 24mm. I think that means a can chain replacement. Looking to do this once and right. Any helpful tips on this? Going to do the valve clearance along with this. Send in tips if ya got em!
  13. Bigwalleye

    Cam cover gasket tear

    Hay - got a 2015 roadster with 7800 miles and noticed a tear on the cam cover seal. Not sure how it tore. what else should I do while I am replacing that seal. Bike is bone stock. I have basic mechanical skills and on a budget. Thanks
  14. Smitty81

    Cam Cover Gasket (again)

    So last year I had my cam cover gasket replaced under warranty, as it suffered the known issue of bulging out just forward of the front-most cylinder. My second gasket is now bulging in the same spot, but also it looks like it contracted back underneath the cam cover at the front right corner...
  15. R3Tex

    Innovv K-2 Dash Cam

    Soooo...never really been one for recording much video during a ride. I have a GoPro that I've played around with, but never really got the hang of it and the videos I took weren't even that interesting to me so I lost interest. However, I am in the early planning stages of a ride from Prudhoe...
  16. A

    Cam chain, guides and 22mm drop in tensioner

    Hello all I have a 2005 rocket and I checked the drop in the plunger with a caliper it read 22mm I installed the spacer now I want to know how long I have left before I need to tear it down and replace the chain guides chain etc I plan on changing the lower sprocket cam sprockets the chain...
  17. mstraub72

    Asking for help with Cam Cover Gasket replacement

    Good afternoon all! My '15 R3R has about 16k miles, and the stupid cam cover gasket has started sweating like a bunch of us have experienced I've discovered after using the Search tool. So, likely over my head, but feeling brave, I decided to tackle it. I've got the tank safely off, I've...
  18. lunatic

    Manual Cam Chain Tensioner

    Ok, I have a question. How do you adjust this with out putting too much tension on the guide and causing premature wear on the chain guides? With the clutch cover off you can visually see it moving and feel the tension. Whats too much and whats not enough? If the cover was on I don't see how...
  19. Jfcroni

    For Sale APE Manual Cam Chain Tensioner ST750

    Make an offer for this Cam Chain Tensioner.
  20. Scholle

    Engine Overhauling - Cam replacement

    My 05 Rocket did not run clean after 240,000 km. The engine no longer cleanly picked up gas in the upper engine speed range, cylinders 2 and 3 had a lower compression than the 1st cylinder. So I had the engine removed and disassembled. Although the fault was with the defective cylinder head...
Top
AdBlock Detected

We get it, advertisements are annoying!

Ad-blocking software does a great job at blocking ads, but it also blocks some useful and important features of R3Owners. For the best possible site experience please take a moment to disable your AdBlocker for R3Owners.Net.

I've Disabled AdBlock